Our OBD2 to USB ELM327 Cable Scan Tool is perfect for automotive enthusiasts and professionals. Featuring genuine FTDI FT232RL and Microchip PIC18F25K80 chips, it supports Windows, Mac OSX, and Linux. With a 1.5m cable length, it reads and clears engine trouble codes, displays real-time data and graphs, and helps prevent potential issues. Compatible with most OBDII vehicles, it’s an essential tool for proactive vehicle maintenance. Paired with one of the many compatible diagnostic software or application, the OBD2 USB Cable allows you to easily scan and clear engine codes, view and record real-time engine and performance data, view emissions status and much more. Software options:OBD Auto Doctor – Suits all OBD2 cars and will allow you to check engine fault codes and clear them and also check engine sensors data. Works on Mac and Windows computers.IMPORTANT NOTICE: Please note that while other software may work with this scan tool to access other modules aside from the engine, OBD2 Australia advertises and describes this device as a basic scanner only for scanning engine fault codes and viewing live engine data. We do not make any claims of this scanner being able to access other modules other than the engine ECU. Return reasons of product incompatibility/non-working functions due to usage that is beyond its advertised and described function will be subject to our Returns Policy and Terms & Conditions. Features: It features a stable, high quality, genuine Microchip PIC18F25K80 micro-controller which adds key features such as automatic protocol search and identification and low power consumption. Vehicle Coverage: Works on all OBDII Vehicles (2006 in USA) and EOBD vehicles.For your vehicle to be OBDII compliant it must have a 16-pin DLC (DataLink Connector) under the dash. Multi-Protocol Support: ISO 9141-2 (5 baud init, 10.4 kbaud)ISO 14230-4 KWP (5 baud init, 10.4 kbaud) (KWP2000)ISO 14230-4 KWP (fast init, 10.4 kbaud) (KWP2000)ISO 15765-4 CAN (11 bit ID, 500 kbaud)ISO 15765-4 CAN (29 bit ID, 500 kbaud)ISO 15765-4 CAN (11 bit ID, 250 kbaud)ISO 15765-4 CAN (29 bit ID, 250 kbaud)SAE J1850 PWM (Older Ford vehicles)SAE J1850 VPW (Older GM vehicles) With the appropriate diagnostics software or application, the ELM327 USB can perform the following operations: Read engine diagnostic trouble codes, both generic and manufacturer-specific, anddisplay code descriptions with over 3000 universal code definitions inthe database (software dependent).Clear diagnostic trouble codes and turn off check engine lights (software dependent).Display and record real-time sensor data, including (software dependent).:Engine RPMCoolant TemperatureCalculated Load ValueFuel System StatusMPH SpeedShort Term Fuel TrimLong Term Fuel TrimIntake Manifold PressureTiming AdvanceIntake Air TemperatureAir Flow RateAbsolute Throttle PositionOxygen Sensor Voltages/Associated Short Term Fuel TrimsFuel System StatusFuel Pressure More Automatically searches for the correct protocol or can be configured manually (software dependent)..Status LEDLength with USB Lead : 1.5 metresRS232 baud rates to 500 KbpsAdaptive Timing automatically adjusts ST timeoutsPower up to AT MA is selectableSource (tester) address can be changedCan reset all PPs with a jumperReceive addresses can be independently setA 4800 baud ISO optionCAN extended addressing supportYou can now perform ISO/KWP bus initialisations without having to send a requestAn SS command allows searching through the OBD protocols sequentiallyA new TA command allows the Tester Address to be easily changedFactory calibration for the voltage reading circuit can be easily restoredISO 9141 and ISO 14230:The slow initiation address can now be variedControl over key word checkingKWP protocols can now transmit 3 or 4 byte headers Specifications: Connection: USB 2.0/1.1Baud Rate: 9600 or 38400Indicator LEDs: OBD Tx/Rx , RS232 Tx/Rx , PowerVoltage: 12VUSB to Serial Chip: FTDI FT232RL USB to UARTFirmware Version: 1.5 Microchip PIC18F25K80 Specifications: Program memory: 32K FlashCPU Speed: 16 MIPSRAM: 3,648 bytesData EEPROM: 1024 bypesADC (Analog to Digital Converter): 8 ch, 12-bitComparators: 2 Driver: The driver is required to be installed prior to use to get this scanner to work with your computer.https://ftdichip.com/wp-content/uploads/2021/08/CDM212364_Setup.zip PRODUCT LIMITATION:This device does not work with any FIAT vehicle or with software called MULTIECUSCAN. This device does not work with FORScan. For a list of FORScan compatible devices, see HERE.
